Documentation / devicetree / bindings / mtd / ingenic,jz4780-nand.txt


Based on kernel version 5.7.10. Page generated on 2020-07-23 22:17 EST.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92
* Ingenic JZ4780 NAND/ECC

This file documents the device tree bindings for NAND flash devices on the
JZ4780. NAND devices are connected to the NEMC controller (described in
memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must
be children of the NEMC node.

Required NAND controller device properties:
- compatible: Should be one of:
  * ingenic,jz4740-nand
  * ingenic,jz4725b-nand
  * ingenic,jz4780-nand
- reg: For each bank with a NAND chip attached, should specify a bank number,
  an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).

Optional NAND controller device properties:
- ecc-engine: To make use of the hardware ECC controller, this
  property must contain a phandle for the ECC controller node. The required
  properties for this node are described below. If this is not specified,
  software ECC will be used instead.

Optional children nodes:
- Individual NAND chips are children of the NAND controller node.

Required children node properties:
- reg: An integer ranging from 1 to 6 representing the CS line to use.

Optional children node properties:
- nand-ecc-step-size: ECC block size in bytes.
- nand-ecc-strength: ECC strength (max number of correctable bits).
- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default
- nand-on-flash-bbt: boolean to enable on flash bbt option, if not present false
- rb-gpios: GPIO specifier for the busy pin.
- wp-gpios: GPIO specifier for the write protect pin.

Optional child node of NAND chip nodes:
- partitions: see Documentation/devicetree/bindings/mtd/partition.txt

Example:

nemc: nemc@13410000 {
	...

	nandc: nand-controller@1 {
		compatible = "ingenic,jz4780-nand";
		reg = <1 0 0x1000000>;	/* Bank 1 */

		#address-cells = <1>;
		#size-cells = <0>;

		ecc-engine = <&bch>;

		nand@1 {
			reg = <1>;

			nand-ecc-step-size = <1024>;
			nand-ecc-strength = <24>;
			nand-ecc-mode = "hw";
			nand-on-flash-bbt;

			rb-gpios = <&gpa 20 GPIO_ACTIVE_LOW>;
			wp-gpios = <&gpf 22 GPIO_ACTIVE_LOW>;

			partitions {
				#address-cells = <2>;
				#size-cells = <2>;
				...
			}
		};
	};
};

The ECC controller is a separate SoC component used for error correction on
NAND devices. The following is a description of the device properties for a
ECC controller.

Required ECC properties:
- compatible: Should be one of:
  * ingenic,jz4740-ecc
  * ingenic,jz4725b-bch
  * ingenic,jz4780-bch
- reg: Should specify the ECC controller registers location and length.
- clocks: Clock for the ECC controller.

Example:

bch: bch@134d0000 {
	compatible = "ingenic,jz4780-bch";
	reg = <0x134d0000 0x10000>;

	clocks = <&cgu JZ4780_CLK_BCH>;
};