About Kernel Documentation Linux Kernel Contact Linux Resources Linux Blog

Documentation / devicetree / bindings / phy / qcom-qusb2-phy.txt


Based on kernel version 5.6.13. Page generated on 2020-05-15 16:46 EST.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68
Qualcomm QUSB2 phy controller
=============================

QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.

Required properties:
 - compatible: compatible list, contains
	       "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
	       "qcom,msm8998-qusb2-phy" for 10nm PHY on msm8998,
	       "qcom,sdm845-qusb2-phy" for 10nm PHY on sdm845.

 - reg: offset and length of the PHY register set.
 - #phy-cells: must be 0.

 - clocks: a list of phandles and clock-specifier pairs,
	   one for each entry in clock-names.
 - clock-names: must be "cfg_ahb" for phy config clock,
			"ref" for 19.2 MHz ref clk,
			"iface" for phy interface clock (Optional).

 - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
 - vdda-phy-dpdm-supply: Phandle to 3.1V regulator supply to Dp/Dm port signals.

 - resets: Phandle to reset to phy block.

Optional properties:
 - nvmem-cells: Phandle to nvmem cell that contains 'HS Tx trim'
		tuning parameter value for qusb2 phy.

 - qcom,tcsr-syscon: Phandle to TCSR syscon register region.
 - qcom,imp-res-offset-value: It is a 6 bit value that specifies offset to be
		added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
		tuning parameter that may vary for different boards of same SOC.
		This property is applicable to only QUSB2 v2 PHY (sdm845).
 - qcom,hstx-trim-value: It is a 4 bit value that specifies tuning for HSTX
		output current.
		Possible range is - 15mA to 24mA (stepsize of 600 uA).
		See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
		This property is applicable to only QUSB2 v2 PHY (sdm845).
		Default value is 22.2mA for sdm845.
 - qcom,preemphasis-level: It is a 2 bit value that specifies pre-emphasis level.
		Possible range is 0 to 15% (stepsize of 5%).
		See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
		This property is applicable to only QUSB2 v2 PHY (sdm845).
		Default value is 10% for sdm845.
- qcom,preemphasis-width: It is a 1 bit value that specifies how long the HSTX
		pre-emphasis (specified using qcom,preemphasis-level) must be in
		effect. Duration could be half-bit of full-bit.
		See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
		This property is applicable to only QUSB2 v2 PHY (sdm845).
		Default value is full-bit width for sdm845.

Example:
	hsusb_phy: phy@7411000 {
		compatible = "qcom,msm8996-qusb2-phy";
		reg = <0x7411000 0x180>;
		#phy-cells = <0>;

		clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
			<&gcc GCC_RX1_USB2_CLKREF_CLK>,
		clock-names = "cfg_ahb", "ref";

		vdda-pll-supply = <&pm8994_l12>;
		vdda-phy-dpdm-supply = <&pm8994_l24>;

		resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
		nvmem-cells = <&qusb2p_hstx_trim>;
        };


About Kernel Documentation Linux Kernel Contact Linux Resources Linux Blog