Based on kernel version 6.8
. Page generated on 2024-03-11 21:26 EST
.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 | * Texas Instruments - lm3532 White LED driver with ambient light sensing capability. The LM3532 provides the 3 high-voltage, low-side current sinks. The device is programmable over an I2C-compatible interface and has independent current control for all three channels. The adaptive current regulation method allows for different LED currents in each current sink thus allowing for a wide variety of backlight and keypad applications. The main features of the LM3532 include dual ambient light sensor inputs each with 32 internal voltage setting resistors, 8-bit logarithmic and linear brightness control, dual external PWM brightness control inputs, and up to 1000:1 dimming ratio with programmable fade in and fade out settings. Required properties: - compatible : "ti,lm3532" - reg : I2C slave address - #address-cells : 1 - #size-cells : 0 Optional properties: - enable-gpios : gpio pin to enable (active high)/disable the device. - ramp-up-us - The Run time ramp rates/step are from one current set-point to another after the device has reached its initial target set point from turn-on - ramp-down-us - The Run time ramp rates/step are from one current set-point to another after the device has reached its initial target set point from turn-on Range for ramp settings: 8us - 65536us Optional properties if ALS mode is used: - ti,als-vmin - Minimum ALS voltage defined in Volts - ti,als-vmax - Maximum ALS voltage defined in Volts Per the data sheet the max ALS voltage is 2V and the min is 0V - ti,als1-imp-sel - ALS1 impedance resistor selection in Ohms - ti,als2-imp-sel - ALS2 impedance resistor selection in Ohms Range for impedance select: 37000 Ohms - 1190 Ohms Values above 37kohms will be set to the "High Impedance" setting - ti,als-avrg-time-us - Determines the length of time the device needs to average the two ALS inputs. This is only used if the input mode is LM3532_ALS_INPUT_AVRG. Range: 17920us - 2293760us - ti,als-input-mode - Determines how the device uses the attached ALS devices. 0x00 - ALS1 and ALS2 input average 0x01 - ALS1 Input 0x02 - ALS2 Input 0x03 - Max of ALS1 and ALS2 Required child properties: - reg : Indicates control bank the LED string is controlled by - led-sources : see Documentation/devicetree/bindings/leds/common.txt - ti,led-mode : Defines if the LED strings are manually controlled or if the LED strings are controlled by the ALS. 0x00 - LED strings are I2C controlled via full scale brightness control register 0x01 - LED strings are ALS controlled Optional LED child properties: - label : see Documentation/devicetree/bindings/leds/common.txt - linux,default-trigger : see Documentation/devicetree/bindings/leds/common.txt - led-max-microamp : Defines the full scale current value for each control bank. The range is from 5000uA-29800uA in increments of 800uA. Example: led-controller@38 { compatible = "ti,lm3532"; #address-cells = <1>; #size-cells = <0>; reg = <0x38>; enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>; ramp-up-us = <1024>; ramp-down-us = <65536>; ti,als-vmin = <0>; ti,als-vmax = <2000>; ti,als1-imp-sel = <4110>; ti,als2-imp-sel = <2180>; ti,als-avrg-time-us = <17920>; ti,als-input-mode = <0x00>; led@0 { reg = <0>; led-sources = <2>; ti,led-mode = <1>; led-max-microamp = <21800>; label = ":backlight"; linux,default-trigger = "backlight"; }; led@1 { reg = <1>; led-sources = <1>; ti,led-mode = <0>; label = ":kbd_backlight"; }; }; For more product information please see the links below: https://www.ti.com/product/LM3532 |