Documentation / devicetree / bindings / mailbox / fsl,mu.yaml


Based on kernel version 6.8. Page generated on 2024-03-11 21:26 EST.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/mailbox/fsl,mu.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: NXP i.MX Messaging Unit (MU)

maintainers:
  - Dong Aisheng <aisheng.dong@nxp.com>

description: |
  The Messaging Unit module enables two processors within the SoC to
  communicate and coordinate by passing messages (e.g. data, status
  and control) through the MU interface. The MU also provides the ability
  for one processor to signal the other processor using interrupts.
 
  Because the MU manages the messaging between processors, the MU uses
  different clocks (from each side of the different peripheral buses).
  Therefore, the MU must synchronize the accesses from one side to the
  other. The MU accomplishes synchronization using two sets of matching
  registers (Processor A-facing, Processor B-facing).

properties:
  compatible:
    oneOf:
      - const: fsl,imx6sx-mu
      - const: fsl,imx7ulp-mu
      - const: fsl,imx8ulp-mu
      - const: fsl,imx8-mu-scu
      - const: fsl,imx8-mu-seco
      - const: fsl,imx93-mu-s4
      - const: fsl,imx8ulp-mu-s4
      - items:
          - const: fsl,imx93-mu
          - const: fsl,imx8ulp-mu
      - items:
          - enum:
              - fsl,imx7s-mu
              - fsl,imx8mq-mu
              - fsl,imx8mm-mu
              - fsl,imx8mn-mu
              - fsl,imx8mp-mu
              - fsl,imx8qm-mu
              - fsl,imx8qxp-mu
          - const: fsl,imx6sx-mu
      - description: To communicate with i.MX8 SCU with fast IPC
        items:
          - const: fsl,imx8-mu-scu
          - enum:
              - fsl,imx8qm-mu
              - fsl,imx8qxp-mu
          - const: fsl,imx6sx-mu

  reg:
    maxItems: 1

  interrupts:
    minItems: 1
    maxItems: 2

  interrupt-names:
    minItems: 1
    items:
      - const: tx
      - const: rx
 
  "#mbox-cells":
    description: |
      <&phandle type channel>
      phandle   : Label name of controller
      type      : Channel type
      channel   : Channel number
 
      This MU support 6 type of unidirectional channels, each type
      has 4 channels except RST channel which only has 1 channel.
      A total of 21 channels.  Following types are
      supported:
      0 - TX channel with 32bit transmit register and IRQ transmit
          acknowledgment support.
      1 - RX channel with 32bit receive register and IRQ support
      2 - TX doorbell channel. Without own register and no ACK support.
      3 - RX doorbell channel.
      4 - RST channel
      5 - Tx doorbell channel. With S/W ACK from the other side.
    const: 2

  clocks:
    maxItems: 1

  fsl,mu-side-b:
    description: boolean, if present, means it is for side B MU.
    type: boolean

  power-domains:
    maxItems: 1

required:
  - compatible
  - reg
  - interrupts
  - "#mbox-cells"

allOf:
  - if:
      properties:
        compatible:
          enum:
            - fsl,imx93-mu-s4
    then:
      properties:
        interrupt-names:
          minItems: 2
        interrupts:
          minItems: 2

    else:
      properties:
        interrupts:
          maxItems: 1
      not:
        required:
          - interrupt-names

additionalProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/arm-gic.h>
 
    mailbox@5d1b0000 {
        compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
        reg = <0x5d1b0000 0x10000>;
        interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
        #mbox-cells = <2>;
    };