Based on kernel version 4.3. Page generated on 2015-11-02 12:45 EST.
1 Device-Tree bindings for LVDS Display Bridge (ldb) 2 3 LVDS Display Bridge 4 =================== 5 6 The LVDS Display Bridge device tree node contains up to two lvds-channel 7 nodes describing each of the two LVDS encoder channels of the bridge. 8 9 Required properties: 10 - #address-cells : should be <1> 11 - #size-cells : should be <0> 12 - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb". 13 Both LDB versions are similar, but i.MX6 has an additional 14 multiplexer in the front to select any of the four IPU display 15 interfaces as input for each LVDS channel. 16 - gpr : should be <&gpr> on i.MX53 and i.MX6q. 17 The phandle points to the iomuxc-gpr region containing the LVDS 18 control register. 19 - clocks, clock-names : phandles to the LDB divider and selector clocks and to 20 the display interface selector clocks, as described in 21 Documentation/devicetree/bindings/clock/clock-bindings.txt 22 The following clocks are expected on i.MX53: 23 "di0_pll" - LDB LVDS channel 0 mux 24 "di1_pll" - LDB LVDS channel 1 mux 25 "di0" - LDB LVDS channel 0 gate 26 "di1" - LDB LVDS channel 1 gate 27 "di0_sel" - IPU1 DI0 mux 28 "di1_sel" - IPU1 DI1 mux 29 On i.MX6q the following additional clocks are needed: 30 "di2_sel" - IPU2 DI0 mux 31 "di3_sel" - IPU2 DI1 mux 32 The needed clock numbers for each are documented in 33 Documentation/devicetree/bindings/clock/imx5-clock.txt, and in 34 Documentation/devicetree/bindings/clock/imx6q-clock.txt. 35 36 Optional properties: 37 - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q 38 - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53, 39 not used on i.MX6q 40 - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should 41 be configured - one input will be distributed on both outputs in dual 42 channel mode 43 44 LVDS Channel 45 ============ 46 47 Each LVDS Channel has to contain either an of graph link to a panel device node 48 or a display-timings node that describes the video timings for the connected 49 LVDS display as well as the fsl,data-mapping and fsl,data-width properties. 50 51 Required properties: 52 - reg : should be <0> or <1> 53 - port: Input and output port nodes with endpoint definitions as defined in 54 Documentation/devicetree/bindings/graph.txt. 55 On i.MX5, the internal two-input-multiplexer is used. Due to hardware 56 limitations, only one input port (port@[0,1]) can be used for each channel 57 (lvds-channel@[0,1], respectively). 58 On i.MX6, there should be four input ports (port@[0-3]) that correspond 59 to the four LVDS multiplexer inputs. 60 A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected 61 to a panel input port. Optionally, the output port can be left out if 62 display-timings are used instead. 63 64 Optional properties (required if display-timings are used): 65 - display-timings : A node that describes the display timings as defined in 66 Documentation/devicetree/bindings/video/display-timing.txt. 67 - fsl,data-mapping : should be "spwg" or "jeida" 68 This describes how the color bits are laid out in the 69 serialized LVDS signal. 70 - fsl,data-width : should be <18> or <24> 71 72 example: 73 74 gpr: iomuxc-gpr@53fa8000 { 75 /* ... */ 76 }; 77 78 ldb: ldb@53fa8008 { 79 #address-cells = <1>; 80 #size-cells = <0>; 81 compatible = "fsl,imx53-ldb"; 82 gpr = <&gpr>; 83 clocks = <&clks IMX5_CLK_LDB_DI0_SEL>, 84 <&clks IMX5_CLK_LDB_DI1_SEL>, 85 <&clks IMX5_CLK_IPU_DI0_SEL>, 86 <&clks IMX5_CLK_IPU_DI1_SEL>, 87 <&clks IMX5_CLK_LDB_DI0_GATE>, 88 <&clks IMX5_CLK_LDB_DI1_GATE>; 89 clock-names = "di0_pll", "di1_pll", 90 "di0_sel", "di1_sel", 91 "di0", "di1"; 92 93 /* Using an of-graph endpoint link to connect the panel */ 94 lvds-channel@0 { 95 #address-cells = <1>; 96 #size-cells = <0>; 97 reg = <0>; 98 99 port@0 { 100 reg = <0>; 101 102 lvds0_in: endpoint { 103 remote-endpoint = <&ipu_di0_lvds0>; 104 }; 105 }; 106 107 port@2 { 108 reg = <2>; 109 110 lvds0_out: endpoint { 111 remote-endpoint = <&panel_in>; 112 }; 113 }; 114 }; 115 116 /* Using display-timings and fsl,data-mapping/width instead */ 117 lvds-channel@1 { 118 #address-cells = <1>; 119 #size-cells = <0>; 120 reg = <1>; 121 fsl,data-mapping = "spwg"; 122 fsl,data-width = <24>; 123 124 display-timings { 125 /* ... */ 126 }; 127 128 port@1 { 129 reg = <1>; 130 131 lvds1_in: endpoint { 132 remote-endpoint = <&ipu_di1_lvds1>; 133 }; 134 }; 135 }; 136 }; 137 138 panel: lvds-panel { 139 /* ... */ 140 141 port { 142 panel_in: endpoint { 143 remote-endpoint = <&lvds0_out>; 144 }; 145 }; 146 };