About Kernel Documentation Linux Kernel Contact Linux Resources Linux Blog

Documentation / devicetree / bindings / net / fsl-fec.txt




Custom Search

Based on kernel version 4.7.2. Page generated on 2016-08-22 22:42 EST.

1	* Freescale Fast Ethernet Controller (FEC)
2	
3	Required properties:
4	- compatible : Should be "fsl,<soc>-fec"
5	- reg : Address and length of the register set for the device
6	- interrupts : Should contain fec interrupt
7	- phy-mode : See ethernet.txt file in the same directory
8	
9	Optional properties:
10	- phy-reset-gpios : Should specify the gpio for phy reset
11	- phy-reset-duration : Reset duration in milliseconds.  Should present
12	  only if property "phy-reset-gpios" is available.  Missing the property
13	  will have the duration be 1 millisecond.  Numbers greater than 1000 are
14	  invalid and 1 millisecond will be used instead.
15	- phy-reset-active-high : If present then the reset sequence using the GPIO
16	  specified in the "phy-reset-gpios" property is reversed (H=reset state,
17	  L=operation state).
18	- phy-supply : regulator that powers the Ethernet PHY.
19	- phy-handle : phandle to the PHY device connected to this device.
20	- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory.
21	  Use instead of phy-handle.
22	- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports
23	  hw multi queues. Should specify the tx queue number, otherwise set tx queue
24	  number to 1.
25	- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports
26	  hw multi queues. Should specify the rx queue number, otherwise set rx queue
27	  number to 1.
28	- fsl,magic-packet : If present, indicates that the hardware supports waking
29	  up via magic packet.
30	
31	Optional subnodes:
32	- mdio : specifies the mdio bus in the FEC, used as a container for phy nodes
33	  according to phy.txt in the same directory
34	
35	Example:
36	
37	ethernet@83fec000 {
38		compatible = "fsl,imx51-fec", "fsl,imx27-fec";
39		reg = <0x83fec000 0x4000>;
40		interrupts = <87>;
41		phy-mode = "mii";
42		phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */
43		local-mac-address = [00 04 9F 01 1B B9];
44		phy-supply = <&reg_fec_supply>;
45	};
46	
47	Example with phy specified:
48	
49	ethernet@83fec000 {
50		compatible = "fsl,imx51-fec", "fsl,imx27-fec";
51		reg = <0x83fec000 0x4000>;
52		interrupts = <87>;
53		phy-mode = "mii";
54		phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */
55		local-mac-address = [00 04 9F 01 1B B9];
56		phy-supply = <&reg_fec_supply>;
57		phy-handle = <&ethphy>;
58		mdio {
59			ethphy: ethernet-phy@6 {
60				compatible = "ethernet-phy-ieee802.3-c22";
61				reg = <6>;
62				max-speed = <100>;
63			};
64		};
65	};
Hide Line Numbers
About Kernel Documentation Linux Kernel Contact Linux Resources Linux Blog

Information is copyright its respective author. All material is available from the Linux Kernel Source distributed under a GPL License. This page is provided as a free service by mjmwired.net.